View TDA7010T_1070555.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

INTEGRATED CIRCUITS
DATA SHEET
TDA7010T FM radio circuit
Product specification File under Integrated Circuits, IC01 September 1983
Philips Semiconductors
Product specification
FM radio circuit
GENERAL DESCRIPTION
TDA7010T
The TDA7010T is a monolithic integrated circuit for mono FM portable radios, where a minimum on peripheral components is important (small dimensions and low costs). The IC has an FLL (Frequency-Locked-Loop) system with an intermediate frequency of 70 kHz. The i.f. selectivity is obtained by active RC filters. The only function which needs alignment is the resonant circuit for the oscillator, thus selecting the reception frequency. Spurious reception is avoided by means of a mute circuit, which also eliminates too noisy input signals. Special precautions are taken to meet the radiation requirements. The TDA7010T includes the following functions: * R.F. input stage * Mixer * Local oscillator * I.F. amplifier/limiter * Phase demodulator * Mute detector * Mute switch QUICK REFERENCE DATA Supply voltage range (pin 4) Supply current at VP = 4,5 V R.F. input frequency range Sensitivity for -3 dB limiting (e.m.f. voltage) (source impedance: 75 ; mute disabled) Signal handling (e.m.f. voltage) (source impedance: 75 ) A.F. output voltage at RL = 22 k PACKAGE OUTLINE 16-lead mini-pack; plastic (SO16; SOT109A); SOT109-1; 1996 July 24. EMF Vo typ. typ. 200 mV 75 mV EMF typ. 1,5 V VP IP frf 2,7 to 10 V typ. 8 mA 1,5 to 110 MHz
September 1983
2
Philips Semiconductors
Product specification
FM radio circuit
TDA7010T
Fig.1 Block diagram.
September 1983
3
Philips Semiconductors
Product specification
FM radio circuit
RATINGS Limiting values in accordance with the Absolute Maximum System (IEC 134) Supply voltage (pin 4) Oscillator voltage (pin 5) Total power dissipation Storage temperature range Operating ambient temperature range VP V6-5 Tstg Tamb max.
TDA7010T
12 V
VP-0,5 to VP + 0,5 V -55 to + 150 C 0 to + 60 C
see derating curve Fig.2
Fig.2 Power derating curve.
D.C. CHARACTERISTICS VP = 4,5 V; Tamb 25 C; measured in Fig.4; unless otherwise specified PARAMETER Supply voltage (pin 4) Supply current at VP = 4,5 V Oscillator current (pin 5) Voltage at pin 12 Output current at pin 2 Voltage at pin 2; RL = 22 k IP I5 V12-14 I2 V2-14 - - - - - 8 280 1,35 60 1,3 - - - - - mA A V A V SYMBOL VP MIN. 2,7 TYP. 4,5 MAX. 10 V UNIT
September 1983
4
Philips Semiconductors
Product specification
FM radio circuit
TDA7010T
A.C. CHARACTERISTICS Vp = 4,5 V; Tamb = 25 C; measured in Fig.4 (mute switch open, enabled); frf = 96 MHz (tuned to max. signal at 5 V e.m.f.) modulated with f = 22,5 kHz; fm = 1 kHz; EMF = 0,2 mV (e.m.f. voltage at a source impedance of 75 ); r.m.s. noise voltage measured unweighted (f = 300 Hz to 20 kHz); unless otherwise specified. PARAMETER Sensitivity (see Fig.3) (e.m.f. voltage) for -3 dB limiting; muting disabled for -3 dB muting for S/N = 26 dB Signal handling (e.m.f. voltage) for THD < 10%; f = 75 kHz Signal-to-noise ratio Total harmonic distortion at f = 22,5 kHz at f = 75 kHz AM suppression of output voltage (ratio of the AM output signal referred to the FM output signal) FM signal: fm = 1 kHz; f = 75 kHz AM signal: fm = 1 kHz; m = 80% Ripple rejection (VP = 100 mV; f = 1 kHz) Oscillator voltage (r.m.s. value) at pin 5 Variation of oscillator frequency with supply voltage (VP = 1 V) Selectivity A.F.C. range Audio bandwidth at Vo = 3 dB measured with pre-emphasis (t = 50 s) A.F. output voltage (r.m.s. value) at RL = 22 k Load resistance at VP = 4,5 V at VP = 9,0 V RL RL - - - - 22 47 k k Vo(rms) - 75 - mV B - 10 - kHz fosc S+300 S-300 frf - - - - 60 43 28 300 - - - - kHz/V dB dB kHz AMS RR V5-4(rms) - - - 50 10 250 - - - dB dB mV THD THD - - 0,7 2,3 - - % % EMF S/N - - 200 60 - - mV dB EMF EMF EMF - - - 1,5 6 5,5 - - - V V V SYMBOL MIN. TYP. MAX. UNIT
September 1983
5
Philips Semiconductors
Product specification
FM radio circuit
TDA7010T
Fig.3
A.F. output voltage (Vo) and total harmonic distortion (THD) as a function of the e.m.f. input voltage (EMF) with a source impedance (RS) of 75 : (1) muting system enabled; (2) muting system disabled.
Conditions:
0 dB = 75 mV; frf = 96 MHz. for S + N curve: f = 22,5 kHz; fm = 1 kHz. for THD curve: f = 75 kHz; fm = 1 kHz.
Note 1. The muting system can be disabled by feeding a current of about 20 A into pin 1.
September 1983
6
Philips Semiconductors
Product specification
FM radio circuit
TDA7010T
Fig.4 Test circuit; for printed-circuit boards see Figs 5 and 6.
September 1983
7
Philips Semiconductors
Product specification
FM radio circuit
TDA7010T
Fig.5 Track side of printed-circuit board used for the circuit of Fig.4.
Fig.6 Component side of printed-circuit board showing component layout used for the circuit of Fig.4.
September 1983
8
Philips Semiconductors
Product specification
FM radio circuit
PACKAGE OUTLINE SO16: plastic small outline package; 16 leads; body width 3.9 mm
TDA7010T
SOT109-1
D
E
A X
c y HE vMA
Z 16 9
Q A2 A1 pin 1 index Lp 1 e bp 8 wM L detail X (A 3) A
0
2.5 scale
5 mm
DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT mm inches A max. 1.75 A1 0.25 0.10 A2 1.45 1.25 A3 0.25 0.01 bp 0.49 0.36 c 0.25 0.19 D (1) 10.0 9.8 E (1) 4.0 3.8 0.16 0.15 e 1.27 HE 6.2 5.8 L 1.05 Lp 1.0 0.4 0.039 0.016 Q 0.7 0.6 0.028 0.020 v 0.25 0.01 w 0.25 0.01 y 0.1 Z (1) 0.7 0.3
0.010 0.057 0.069 0.004 0.049
0.019 0.0100 0.39 0.014 0.0075 0.38
0.244 0.050 0.041 0.228
0.028 0.004 0.012
8 0o
o
Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. OUTLINE VERSION SOT109-1 REFERENCES IEC 076E07S JEDEC MS-012AC EIAJ EUROPEAN PROJECTION
ISSUE DATE 95-01-23 97-05-22
September 1983
9
Philips Semiconductors
Product specification
FM radio circuit
SOLDERING Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "IC Package Databook" (order code 9398 652 90011). Reflow soldering Reflow soldering techniques are suitable for all SO packages. Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. Several techniques exist for reflowing; for example, thermal conduction by heated belt. Dwell times vary between 50 and 300 seconds depending on heating method. Typical reflow temperatures range from 215 to 250 C. Preheating is necessary to dry the paste and evaporate the binding agent. Preheating duration: 45 minutes at 45 C. Wave soldering Wave soldering techniques can be used for all SO packages if the following conditions are observed: * A double-wave (a turbulent wave with high upward pressure followed by a smooth laminar wave) soldering technique should be used. * The longitudinal axis of the package footprint must be parallel to the solder flow. * The package footprint must incorporate solder thieves at the downstream end.
TDA7010T
During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Maximum permissible solder temperature is 260 C, and maximum duration of package immersion in solder is 10 seconds, if cooled to less than 150 C within 6 seconds. Typical dwell time is 4 seconds at 250 C. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. Repairing soldered joints Fix the component by first soldering two diagonallyopposite end leads. Use only a low voltage soldering iron (less than 24 V) applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 C. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 C.
September 1983
10
Philips Semiconductors
Product specification
FM radio circuit
DEFINITIONS Data sheet status Objective specification Preliminary specification Product specification Limiting values
TDA7010T
This data sheet contains target or goal specifications for product development. This data sheet contains preliminary data; supplementary data may be published later. This data sheet contains final product specifications.
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale.
September 1983
11

▲Up To Search▲

Price & Availability of TDA7010T

	To Download TDA7010T Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .